Wireless networks

Zigbee
Zigbee lights, covers, thermostats, plugs, sensors and buttons on the hub's own Zigbee network. Needs a Zigbee USB stick in the hub. It runs without internet, but pairing from Partner needs the hub online.
What it does
- Lights: on, off, toggle, brightness, colour and colour temperature.
- Blinds and curtains: open, close, stop and position.
- Thermostats and radiator valves: temperature, mode, and whether they heat or cool right now.
- Plugs and switches: on, off, toggle. A switch with several channels gives one device per channel.
- On/off sensors: occupancy, presence, door contact, water leak, smoke, gas, vibration, tamper.
- Readings: temperature, humidity, light, pressure, battery, power, energy.
- Button presses as events for automations, and batteryless Green Power switches such as the Hue Tap.
- Pairing runs the model's own setup, so it sends its changes by itself.
- You pair devices from Partner, and a command counts once the hub reads it back from the device.
Worth knowing
- Needs a Zigbee USB stick. The driver expects EmberZNet firmware by default, and SFK sets the stick up.
- No locks, sirens, fans or blind tilt.
- A thermostat takes one temperature at a time: no heat and cool range, no schedules or presets.
- Only models the device library knows.
- A sleeping battery device gets its setup the next time it talks, so its updates may start late.
- Checked against real device definitions and a simulated device so far, not yet with a real stick.
Setup guide
Driver: systems.arvio.zigbee. Local: runs without internet. Needs a Zigbee USB stick in the hub.
The hub runs its own Zigbee network. SFK sets up the stick, and you pair the devices yourself in Partner.
What you need
- A Zigbee USB stick in the hub. The driver expects EmberZNet firmware by default, and SFK confirms the model and sets it up. Use a USB 2.0 extension cable.
- The stick plugged in before the hub starts. If it is plugged in later, the driver has to be restarted to see it.
- The hub online while you pair, because Partner reaches it over the internet.
- Your devices, and their manuals for how to put them in pairing mode.
How to connect
- In Partner, open the hub and go to the «Συσκευές» (Devices) tab. Choose «Σύζευξη Zigbee» (Zigbee pairing).
- Press «Άνοιγμα Zigbee 2′». The network stays open for two minutes.
- Put the device in pairing mode.
- The device appears in the list. Put it in a room from «Δωμάτια» (Rooms), and test it.
A switch with several channels joins once and gives one device per channel, with the channel's name at the end (l1, left). Give each its own name and room.
A batteryless Green Power switch joins the same way: while the network is open, do what its manual says for pairing.
Partner can show the network as open even with no working stick in the hub. If nothing joins, check the stick first.
What works
- Lights: on, off, toggle, brightness, colour and colour temperature.
- Blinds and curtains: open, close, stop and position.
- Thermostats and radiator valves: temperature, mode, and whether they heat or cool right now.
- Plugs and switches: on, off, toggle, and each channel on its own.
- On/off sensors: occupancy, presence, door contact, water leak, smoke, gas, vibration, tamper.
- Readings: temperature, humidity, light, pressure, battery, power, energy.
- Button presses as events for automations, and batteryless Green Power switches such as the Hue Tap.
- Pairing runs the model's own setup, so it sends its changes by itself.
- A command counts once the hub reads it back from the device.
Limits
- No locks, sirens, fans or blind tilt.
- A thermostat takes one temperature at a time: no heat and cool range, no schedules or presets.
- Only models the device library knows.
- A sleeping battery device gets its setup the next time it talks, so its updates may start late.
- Checked against real device definitions and a simulated device so far, not yet with a real stick.
Troubleshooting
- Partner says the network is open, and nothing joins → the hub may have no working stick. SFK checks the hub's log and restarts the driver if the stick was plugged in late.
- A device joined but does not show → the device library may not know that model. SFK sees this in the hub's log.
- A sensor does not update → if it runs on a battery, wake it once (press its button, open the door, move in front of it) so it gets its setup. If it stays the same, tell SFK the model.
- A blind or a radiator valve says «δεν έγινε» (not done) → the hub did not see the device move or keep the new value. Check whether it moved. A battery valve answers slowly; try again.
- The stick was unplugged → the driver loses the network until the stick is back and the driver is restarted. Devices stay paired.
- The hub's data was lost → the network's identity lives on the hub. Without it, every device has to pair again.
